Industrial-data-systems IDS DT220 Instrukcja Użytkownika

DT220 Scale Weight Indicator Data Terminal Installation/Calibration/Operation Version 1.c 06/13/08 Industrial Data Systems, Inc. 38

DT220 Users Manual version 1.a Installation and Setup 6 Connect DT220 to host device (optional) Serial Communications Port 2 can provide a co

DT220 Users Manual version 1.a Using the DT220 7 Using the DT220 The DT220 has 8 function keys located at the top of the keyboard, 5 Scale orie

DT220 Users Manual version 1.a Using the DT220 8 Gross/Net Press the Gross/Net key to alternate between Gross and Gross/Tare/Net display modes

DT220 Users Manual version 1.a Using the DT220 9 Weigh / Weigh-In / Weigh-Out The Weigh/Weigh-In/Weigh-out program uses the database (ID) memor

DT220 Users Manual version 1.a Using the DT220 10 The Product ID is highlighted press the Enter key to accept the current ID or key in an ID to

DT220 Users Manual version 1.a Using the DT220 11 Manage Database ID Tables Press the ID Tables function key to access the database management

DT220 Users Manual version 1.a Using the DT220 12 Scan ID’s The display lists the ID keys in alphabetical order along with some additional fie

DT220 Users Manual version 1.a Using the DT220 13 Erase ID The display prompts “Enter Nnnn ID:” where Nnnn is the data table name. Enter an

DT220 Users Manual version 1.a Configuration Parameters 14 Configure Parameters Press the Shift ke

DT220 Users Manual version 1.a Configuration Parameters 15 Scale Parameter 1.1: A/D speed (120 s

Table of Contents Introduction...1 What’s In Ea

DT220 Users Manual version 1.a Configuration Parameters 16 Scale Parameter 5.1: Primary Units Ty

DT220 Users Manual version 1.a Configuration Parameters 17 Scale Parameter 6.3: Zero tracking

DT220 Users Manual version 1.a Configuration Parameters 18 Scale Parameter 8: Power-On Zero (N [

DT220 Users Manual version 1.a Configuration Parameters 19 2. The DT220 prompts “Press ENTER to r

DT220 Users Manual version 1.a Configuration Parameters 20 Adjust Gain – 5 Point Linearization If

DT220 Users Manual version 1.a Configuration Parameters 21 1 - AND: <status>, <mode>

DT220 Users Manual version 1.a Configuration Parameters 22 Printer Select The printer select provi

DT220 Users Manual version 1.a Configuration Parameters 23 Timers There are 9 timers that can be

DT220 Users Manual version 1.a Configuration Parameters 24 Clock Adjust (0) The clock adjust param

DT220 Users Manual version 1.a Configuration Parameters 25 Disable numeric register edit 1&2,

Scale Parameters...14 Scale Paramete

DT220 Users Manual version 1.a Configuration Parameters 26 ID Data Base Tables Selection 7- 9

DT220 Users Manual version 1.a Configuration Parameters 27 Register List Registers List 1-31

DT220 Users Manual version 1.a Configuration Parameters 28 210 Time\date Time and Date 211 Time

DT220 Users Manual version 1.a Configuration Parameters 29 Page 2 Item Description Line No.

DT220 Users Manual version 1.a Configuration Parameters 30 Format Design Worksheets Page Item Des

DT220 Users Manual version 1.a Configuration Parameters 31 Registers There are 79 general-purpose

DT220 Users Manual version 1.a Configuration Parameters 32 System initialize, save Cal. Use this f

DT220 Users Manual version 1.a Configuration Parameters 33 Backlight Adjust Press the Shift key a

DT220 Users Manual version 1.a Diagnostic Tests 34 Diagnostic Tests The DIAGNOSTIC TESTS are accessed using Func. 9 (test/config.) key. The di

DT220 Users Manual version 1.a Diagnostic Tests 35 Memory Display The display prompts “Memory Address: xxxx”. Enter a memory address and pres

MMC Test ...35 TTL Input Test .

DT220 Users Manual version 1.a Troubleshooting 36 Troubleshooting The following table describes the probable causes to some problems you may en

DT220 Users Manual version 1.a Hardware & Wiring 37 Hardware and Wiring This section describes installation and wiring information for the

DT220 Users Manual version 1.a Hardware & Wiring 38 Com Port 1 – J10 and TB6 The serial communication port 1 has a 9 pin ‘D’ connector at t

DT220 Users Manual version 1.a Hardware & Wiring 39 Com Port 2 TB5 Pin # Signal Name 1 485 RX+ 2 485 RX- 3 485 TX+ 4 485 TX-

DT220 Users Manual version 1.a Hardware & Wiring 40 Parallel Printer Port – 25 pin D connector J2 Pin # Signal Name 1 Strobe Output

DT220 Users Manual version 1.a Hardware & Wiring 41 P.C. Board Diagram - Connectors, Jumpers, and Switche

DT220 Users Manual version 1.a Hardware & Wiring 42 Sample Cable Drawings Load Cell IDS Printers/Serial Printers Note: use sense jumper

DT220 Users Manual version 1.a Hardware & Wiring 43 Parallel (Centronix) Printer TTL Input switches GND 2 3 4 3 1 TB 3 DT220 TTL Inp

DT220 Users Manual version 1.a Specifications 44 DT220 Specifications Display 8 lines x 40 char (240x64 graphics) LCD display. Keyboard

DT220 Users Manual version 1.a ASCII Chart 45 ASCII CHART ASCII DEC ASCII DEC ASCII DEC ASCII DEC Null 00

DT220 Users Manual version 1.a Introduction 1 Introduction Congratulations on your purchase and welcome to the DT220 User's Manual. This manua

DT220 Users Manual version 1.a Introduction 2 What’s In Each Section This manual is organized and divided into separate sections: Installation

DT220 Users Manual version 1.a Introduction 3 WARRANTY INFORMATION INDUSTRIAL DATA SYSTEMS, INC. LIMITED WARRANTY. Industrial Data Systems, Inc., w

DT220 Users Manual version 1.a General Description 4 General Description This section gives you a general description on the operation of the D

DT220 Users Manual version 1.a Installation and Setup 5 Installation and Setup This section provides information about unpacking, installing, a